SJD 6-22

About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product.
  
• Observe the safety instructions and warnings in this documentation and on the product.
  
• Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons.
  

Explanation of symbols

Warnings

Symbols in the operating instructions

	Comply with the operating instructions
	Instructions for use and other useful information
	Dealing with recyclable materials
	Do not dispose of electric equipment and batteries as household waste
	Hilti Li‑ion battery
	Hilti charger

Symbols in illustrations

	These numbers refer to the illustrations at the beginning of these operating instructions.
	The numbering reflects the sequence of operations shown in the illustrations and may deviate from the steps described in the text.
	Item reference numbers are used in the overview illustration and refer to the numbers used in the key in the product overview section.
	These characters are intended to specifically draw your attention to certain points when handling the product.

Product-dependent symbols

Additional symbols

	Stroke rate under no load
	Direct current (DC)
	Li‑ion battery
	The product supports near-field communication (NFC) technology compatible with iOS and Android platforms.
	Hilti Li-ion battery type series used. Observe the information given in the section headed Intended use .
	Never use the battery as a striking tool.
	Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any other way.
	If applied on the product, the product has been certified by this certification body for the US and Canadian markets according to the applicable standards.

Product information

• Write down the serial number in the table below. Always quote this information when you contact a Hilti representative or Hilti Service to inquire about the product.
  Product information

  Orbital-action jig saw	SJD 6-22
  Generation	02
  Serial no.

General power tool safety warnings

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
  
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
  
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
  

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
  
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
  
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
  
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
  
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
  
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
  

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
  
• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
  
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
  
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
  
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
  
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
  
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
  
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
  

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
  
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
  
• Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
  
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
  
• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
  
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
  
• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
  
• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
  

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
  
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
  
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
  
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
  
• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
  
• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130° C (265 °F) may cause explosion.
  
• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
  

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
  
• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
  

Safety instructions for reciprocating saws

• Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.
  

• Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the workpiece by hand or against your body leaves it unstable and may lead to loss of control.
  

Additional safety instructions

• Use the product and accessories only when they are in perfect working order.
  
• Never tamper with or modify the product or accessories in any way.
  
• Before beginning work, check the working area for concealed electric cables or gas and water pipes. External metal parts of the product could give you an electric shock or cause an explosion if you accidentally damage an electric cable or a gas or water pipe.
  
• Keep the air vents clear at all times. Risk of burn injuries due to blocked air vents!
  
• Wear eye protection, ear protection and protective gloves while the product is in use.
  
• Wear eye protection. Flying fragments present a risk of injury to the body and eyes.
  
• Dust produced by grinding, sanding, cutting and drilling can contain dangerous chemicals. Some examples are: lead or lead-based paints; brick, concrete and other masonry products, natural stone and other products containing silicates; certain types of wood, such as oak, beech and chemically treated wood; asbestos or materials that contain asbestos. Determine the exposure of the operator and bystanders by means of the hazard classification of the materials to be worked. Implement the necessary measures to restrict exposure to a safe level, for example by the use of a dust collection system or by the wearing of suitable respiratory protection. The general measures for reducing exposure include:
  
• working in an area that is well ventilated,
  
• avoidance of prolonged contact with dust,
  
• directing dust away from the face and body,
  
• wearing protective clothing and washing exposed areas of the skin with water and soap.
  
• Risk of injury by falling tools and/or accessories. Before starting work, check that the battery and installed accessories are secure.
  
• Switch the product on only after you have brought it to the working position.
  
• Always hold the product securely by the grips provided. Keep the grips clean and dry.
  
• Take frequent breaks and do physical exercises to improve the blood circulation in your fingers. High vibration during long periods of work can lead to disorders of the blood vessels and nervous system in the fingers, hands and wrists.
  
• Do not look directly into the light source (LEDs) incorporated in the power tool and do not direct the light at other persons’ faces. Risk of dazzling or eye injury!
  
• Wait until the product has come to a complete stop before you lay it down.
  
• Wear protective gloves when changing the accessory tool. Touching the accessory tool can result in cuts and burns!
  

• Always guide the product away from your body when working with it.
  
• Never position your hands ahead of or on the saw blade.
  
• Never cut into unknown materials and keep the line of cut above and below the workpiece free of obstacles.
  
• Never reach or grip below the workpiece while cutting.
  

Battery use and care

• Comply with the following safety instructions for the safe handling and use of Li-ion batteries. Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire and/or explosion.
  
• Use only batteries that are in perfect working order.
  
• Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely harmful to health!
  
• Do not under any circumstances modify or tamper with batteries!
  
• Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C (176 °F).
  
• Never use or charge a battery that has suffered an impact or been damaged in any other way. Check your batteries regularly for signs of damage.
  
• Never use recycled or repaired batteries.
  
• Never use the battery or a battery-operated power tool as a striking tool.
  
• Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This can lead to explosions.
  
• Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects. This can damage the battery and also cause material damage and personal injury.
  
• Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits, electric shock, burns, fire and explosions.
  
• Use only chargers and power tools approved for the specific battery type. Read and follow the relevant operating instructions.
  
• Do not use or store the battery in explosive environments.
  
• If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to cool down. If it is still too hot to touch after an hour, the battery is faulty. Consult Hilti Service or read the document entitled "Instructions on safety and use for Hilti Li-ion batteries".
  
  Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.
  Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning the QR code at the end of these operating instructions.
  

Product overview

1. Lockbutton
   
2. On/off switch
   
3. Grip
   
4. Battery
   
5. Air vents
   
6. Installation opening for accessories
   
7. Stroke rate regulator thumbwheel
   
8. Saw blade release lever
   
9. Blade holder
   
10. Guard
    
11. Contact guard
    
12. Saw blade
    
13. Anti-splinter insert
    
14. Orbital-action adjustment lever
    
15. Base plate
    
16. Cutting angle adjustment scale
    
17. Catches
    
18. Suction adapter
    
19. Release button, battery
    
20. Battery status indicator
    

Intended use

The product described is a hand-held cordless orbital-action jig saw. It is designed to be used for cutting plastic, wood and metal as well as drywall board and gypsum fiberboard.

• For this product, use only Hilti Nuron lithium-ion batteries of the B 22 series. For optimum performance, Hilti recommends the batteries stated in this table for this product.

• For these batteries, use only Hilti chargers of the type series stated in this table.

• Use this product only with saw blades equipped with a T-shank.

Possible misuse

• Use of the product to cut off tree branches or to cut the trunk of a tree is not permissible.
  
• Use of the product to cut hazardous materials is not permissible.
  
• Use of the product in a damp or wet environment is not permissible.
  

• Keep objects such as paper clips, coins, keys, nails, screws, or other small metal objects, which could cause a short circuit, away from the electric power supply for the dust removal module. A short circuit between the contacts may result in burning injuries or fire.
  

Status indicators of the Li‑ion battery

Indicators for state of charge and fault messages

Indicators showing the battery's state of health

Dust blower

Stroke rate

4 orbital-action settings

Lockbutton

1. The middle position is the normal position: The lockbutton can be seen on the left and on the right. In this position, for example, the stroke rate can be adjusted.
   The on/off switch can be pressed and released.
   
2. The lockbutton can be seen only on the left: Transport position (the product cannot start).
   The on/off switch is locked and cannot be pressed.
   
3. The lockbutton can be seen only on the right: After the product has been switched on (on/off switch fully pressed), the lockbutton can be pushed to the right to lock the switch in the “on” position. To release the lock, press the on/off button again.
   

Anti-splinter insert

Automatic product switch-off

SJD DRS-6A dust removal module (accessory)

Items supplied

Orbital-action jig saw

Battery

Charging the battery

1. Before charging the battery, read the operating instructions for the charger.
   
2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
   
3. Use an approved charger to charge the battery.
   

Inserting the battery

1. Charge the battery fully before using it for the first time.
   
2. Push the battery into the product until it engages with an audible click.
   
3. Check that the battery is seated securely.
   

Removing the battery

1. Press the battery release button.
   
2. Remove the battery from the product.
   

Fitting the saw blade

1. Push the saw blade (teeth facing the cutting direction) into the blade holder until it engages.
   
2. Grip and pull the saw blade to check that it is held securely.
   

Fitting the guard

• Push the guard onto the power tool from the front until it clicks into place.
  
  The guard can be fitted only when the base plate is in the normal position (0° cutting angle).
  

Fitting the dust removal adapter

1. Push the dust removal adapter on to the base plate horizontally from the rear until both catches engage at the side.
   
2. Connect the vacuum cleaner hose to the dust removal adapter.
   

Fitting the anti-splinter insert

• Press the anti-splinter insert into the base plate from below.
  
  The anti-splinter insert can be used only with the saw blades for which it is designed.
  The anti-splinter insert can be used only when the base plate is in the normal position (0° cutting angle).
  

Fall arrest

• Use the loop to secure the tool tether to the product as shown in the illustration. Check that it holds securely.
  
• Secure the carabiner to a load-bearing structure. Check that the carabiner holds securely.
  
  Comply with the operating instructions of the Hilti tool tether.
  

Using a dust extractor

1. Fit the guard.
   
2. Always use a dust extractor when working over a lengthy period with wood or materials that can cause high dust concentrations.
   

Setting the cutting angle

1. Slacken the screw on the base plate.
   
2. Adjust the base plate to the desired cutting angle (from 0° to 45° in both directions).
   
   • At the 0° cutting angle, the base plate is held in a rotation-locked position. To set a different cutting angle, you must first pull the base plate to the rear.
     
   • When you return the base plate to the 0° cutting angle, push the base plate forward again to re-engage it in this rotation-locked position.
     
3. Retighten the screw.
   
   • The base plate is clamped securely.
     

Switching on

1. Check that the lockbutton is in the middle position.
   
2. Press the on/off switch.
   
3. To lock the switch in the “on” position, then push the lockbutton to the right.
   
   • The product then runs in sustained operating mode.
     
4. To release the lockbutton, press the on/off switch again.
   
   • The lockbutton then returns to the middle position.
     

Plunge cutting

1. Set the orbital-action adjusting lever to position 0.
   
2. Bring the front edge of the base plate into contact with the workpiece.
   
3. Hold the product securely and press the on/off switch.
   
4. Press the product firmly against the workpiece and begin the plunge cut by slowly reducing the angle of attack.
   
5. Once the blade has penetrated right through the workpiece, bring the product into its normal working position.
   
   • The base plate then lies flat on the working surface.
     
6. Continue to saw along the cutting line.
   

Switching off

1. Release the on/off switch.
   
2. If the on/off switch is locked in the "on" position, briefly press the on/off switch to disengage the lock and then release the switch.
   
   To lock the switch in the “off” position, push the lockbutton to the left.
   

Removing the suction adapter

1. Press the two retaining catches inwards.
   

2. Pull the suction adapter away from the base plate toward the rear.
   
3. Pull the vacuum cleaner hose off the suction adapter.
   

Removing the guard

• Tilt the guard slightly and pull it off toward the front.
  

Ejecting the saw blade

• Push the saw blade release lever to the side, as far as it will go.
  
  • The saw blade will be released and ejected.
    

Cleaning the suction adapter

1. Remove the suction adapter.
   
2. Clean the suction adapter.
   
3. Check that the catches are undamaged.
   
4. Fit the dust removal adapter.
   

Cleaning the saw blade

1. Clean resin deposits from used saw blades at regular intervals.
   
2. Place the saw blades in a bath of kerosene (paraffin oil) or commercially-available resin remover for 24 hours.